PROJECT OF MINI TESLA COIL VERY EASILY

 How Did You Make A Mini Tesla Coil Very Easily

 At First You Need  This Things To Make This Project

1.20Mx Isolated Copper Wire

2. 1xPlastic Pipe
3. 1x2N2222 Transistor 4. 1xPlastic box 5. 1x9v Battery 6. 1xBattery cap 7. 1x On-Off switch 8. 2x10k Resistance 9. 1x Thick wire


At First Make round shaped winding around a plastic pipe And it must be memorized that it would be 200 turns around the pipe.

Next make a another winding of 3 turns with the thick wire and the winding is placed above the first winding body symbolized in image of red wire






Next take the transistor 2N2222 is a NPN type transistor The Emitter point of transistor is connect to the negative terminal of 9volt battery

Next the on off switch connect to the positive terminal of battery and the point of other wire of switch connect the one side of resistors (the resistor must be in series) and also connect the thick wire's one terminal. The other side of resistor's pin connect with one terminal of Isolated copper wire's one terminal. The last step (The other side of resistor's pin connect with one terminal of Isolated copper wire's one terminal) the pin of resistor's other point with Isolated copper wire connect with base of 2N2222 transistor . like the in the picture.

Next the thick copper wire's another terminal connect with collector point of the transistor.
This is the complete circuit diagram shown in picture









Comments

Post a Comment

Popular posts from this blog

What Is An Inductor?

Image
                     What Is An Inductor? An inductor is a passive electronic component which is capable of storing electrical energy in the form of magnetic energy. Basically, it uses a conductor that is wound into a coil, and when electricity flows into the coil from the left to the right, this will generate a magnetic field in the clockwise direction. The Inductor Basically Used For Increase Or  Decrease Of Current                          One Example On Current Increasing-:  You Are See Here Is A Battery , A  bulb,A coil Of Wire(Inductor) Around A Piece Of Iron(Yellow Coloured) And A Switch The Coil Of Wire Is An Inductor. If You Were To Take Out The Inductor From This Circuit You Get A Normal Light. But When You Connect The Inductor To This Circuit  And Close The Switch The bulb Burns Brightly And Then Quickly Goes Out. It Occur Because Th...
Read more

What Is Transformer?

Image
                                             What Is   Transformer? A transformer is a passive electrical device that transfers electrical energy from one electrical circuit to another, or multiple circuits without change of frequency. A  transformer  consists of two electrically isolated coils and operates on Faraday's principal of “mutual induction”, in which an EMF is induced in the  transformers  secondary coil by the magnetic flux generated by the voltages and currents flowing in the primary coil winding. Working Principle -: The  operation principle  of the  single - phase transformer  is: the AC voltage source injects the AC current through the  transformer  primary winding. ... Thus the voltage is induced in the secondary winding with the same frequency as the voltage of the primary side. The induced voltage val...
Read more

HOW TO MAKE ARDUINO UNO BASED PROJECTS ?

Image
HOW TO MAKE ARDUINO UNO BASED PROJECTS ? At First I Recommend To All My Readers That They Should Be Use A Computer OR Laptop. I Will Be Tell You How Can Upload Programming On Arduino Nano On Another Post. Today I Talk About Arduino Uno Based Projects  At First You Should Go To Arduino's Official Website (https://www.arduino.cc/en/Main/Software)  Here You Can Download Arduino IDE Software And Install It On Your PC. If You Are New On This Project You Should Start From Blink The LED Light . Hardware Required Arduino or Genuino Board optional  1xLED 1x220 ohm resistor If you want to lit an external LED with this sketch, you need to build this circuit, where you connect one end of the resistor to the digital pin correspondent to the  LED_BUILTIN  constant. Connect the long leg of the LED (the positive leg, called the anode) to the other end of the resistor. Connect the short leg of the LED (the negative leg, called the cathode) to the GND. In the diagram below we sho...
Read more